e02ch04.pdf
(
44 KB
)
Pobierz
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01//EN" "http://www.w3.org/TR/html4/strict.dtd">
004
Long-Interval Timer
G. Ruschitzka
+5V
Occasionally there is a need for a timer circuit for tasks such as
switching off a circuit element (such as an LC display) after a
given interval or generating a time delay for an application.
Short intervals can be conveniently generated using a 555
timer, but if the switch-off time lies in the range of minutes or
longer, a 555 is no longer suitable due to the large value
required for the capacitor, which leads to inaccuracies or insta-
bility. In such cases, a digital counter circuit with an oscillator
is a better solution.
The 74HCT4060 IC, with its built-in oscillator, can cover a wide
range of frequencies in a simple and reliable manner and can
also generate very low frequencies. The 14-bit divider chain
can divide the oscillator frequency by up to 16,384, which
makes it easy to obtain long time intervals.
The circuit presented here acts like a digital monostable. The
timeout time starts when the system is switched on, since a
Low level is initially present on the selected output of the
counter IC (Q13 or any other desired output Q2–Q12). This
represents the active (On) state for the connected circuit. After
the counter chain has counted up enough for the selected out-
put to switch to the High state, the oscillator is cut off by tran-
sistor T1 so that no further counting pulses can be generated.
The circuit thus remains in this state. The High signal level rep-
resents a ‘rest state’ for the connected circuit.
In order to reactive the timeout, a positive pulse is applied to
the Reset input (pin 12). The circuit re-triggers, the Q output
goes Low immediately (active) and a new timeout starts.
To make the selection of counter outputs flexible, a DIP switch
can be used as long as only one switch at a time is activated,
since otherwise short circuits will be created between the
counter outputs. It is also useful to connect one of the
switches to V
cc
via a small resistance. If this switch is acti-
vated, the connected circuit is permanently disabled, while if
neither this switch nor any of the other switches is activated,
the circuit is permanently enabled. This covers all possible
operating situations. It is important to keep the load small. If
necessary, a CMOS gate (inverter) can be used to buffer the
C2
C3
R4
47
µ
16V
100n
IC1
16
7
3
4
5
6
7
8
9
CTR14
5
R3
470k
4
!G
11
6
RCX
R1
220k
10
14
+
RX
CT
9
13
CX
C1
R2
2k2
15
1
220n
11
TRIGGER
2
TIMEOUT
12
12
CT=0
3
13
R5
T1
D1
8
74HCT4060N
BAT48
BC237
024065 - 11
ON
TRIGGER
TRIGGER
TRIGGER
OUTPUT
TIMEOUT
TIMEOUT
TIMEOUT
024065 - 12
following circuit.
The timeout interval is given by the formula
timeout = 2
n
÷f
osc
with
n
= selected output stage (
n
= 3–13)
f
osc
= 1 ÷ (2.5
(R1
C1))
With the indicated component values (R1 = 220 k
, C1 =
220 nF), the frequency is 8.3 Hz and the timeout interval at Q13
is 16.5 minutes.
(024065-1)
12/2002
Elektor Electronics
23
Plik z chomika:
gasma
Inne pliki z tego folderu:
bge.jpg
(23 KB)
detail1.htm
(4 KB)
detail2.htm
(4 KB)
e02a016.pdf
(1746 KB)
detail3.htm
(5 KB)
Inne foldery tego chomika:
1974
1975
1976
1977
1978
Zgłoś jeśli
naruszono regulamin