ALP_TRG112 HP Machining Tutorial 2013 R1 V2.2.pdf
(
2097 KB
)
Pobierz
ALP_TRG112
Housing Plate
Machining Tutorial
Housing Plate Machining Tutorial
Page 2 of 44
ALP_TRG112
Housing Plate Machining Tutorial
Copyright
Copyright © 2012 Vero Software Ltd. All rights reserved.
Any copyright or other intellectual property right of whatever nature which subsists or may
subsist in the presentation and/or content of the programs (including without limitation its
look, feel, visual or other non-literal elements) remains the property of Vero Software Ltd or
its licensor(s) absolutely.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval
system or translated into any language, in any form or by any means, electronic,
mechanical, optical, chemical, manual or otherwise, without the express written permission
of Vero Software Ltd.
Unauthorised reproduction or distribution of these programs or any part thereof is unlawful
and may result in civil or criminal penalties.
Alphacam and the Alphacam Logo are trademarks of Vero Software Ltd.
Windows is a trademark of Microsoft Corporation.
All product names mentioned in this publication, and not listed above, are acknowledged as
the trademarks of the respective manufacturers and producers of such products.
Vero Software Ltd makes no representations or warranties with respect to the contents
hereof and specifically disclaim any implied warranties of satisfactory quality or fitness for
any particular purpose. Further, Vero Software Ltd reserves the right to revise this
publication and to make changes in the contents hereof without obligation to notify any
person of such changes or revisions.
The information contained within this document is subject to change without notice and does
not represent a commitment on the part of the vendor. The software described in this
document is furnished under a licence agreement and may be used or copied only in
accordance with the terms of the agreement.
Version 2
Page 3 of 44
A2
Housing Plate Machining Tutorial
Contents
Conventions used in this guide......................................................................... 7
Recommended Operating Systems and Hardware for Alphacam ..................... 8
Supported Operating Systems 8
Alphacam Minimum Specifications 8
Machining 2D Flat Geometry ............................................................................ 9
Geometry Creation ........................................................................................... 9
Housing Plate Process Plan ............................................................................. 9
Machine/Tool Directions .......................................................................... 11
Prepare the Geometry for Machining.............................................................. 11
Tool Directions 11
Hole Geometry Sorting 14
Machining....................................................................................................... 16
Set-up 16
Operation 1 .................................................................................................... 17
Dialog 1
17
17
Dialog 2
Dialog 3
17
Dialog 4
17
Select Geometries
17
Helical Finish 20 & 30 Dia. Holes (Profiles 9,10)
19
19
Dialog 1
Dialog 2
19
19
Dialog 3
Dialog 4
19
19
Select Geometries
Adding or removing geometries from a Machining strategy.
20
Edit the Strategy Parameters
20
Rough & Finish Profile 2, 3mm deep 4 xy cuts 35 stock
21
Dialog 1
21
21
Dialog 2
Dialog 3
21
21
Dialog 4
Select Geometries
21
Rough Profile 1 Outer Edge 16 deep leave 0.5 Stock
22
Dialog 1
22
Dialog 2
22
Dialog 3
22
Dialog 4
22
22
Select Geometries
Page 4 of 44
ALP_TRG112
Housing Plate Machining Tutorial
Operation 2..................................................................................................... 23
Residual Waveform Pocket Profiles 6,7,8 leave 0.5 Stock and Finish Profile to size 23
Dialog 1 23
Dialog 2 23
Dialog 3 23
Dialog 4 23
The Finishing Dialogs will be displayed 23
Dialog 5 23
Dialog 6 24
Dialog 7 24
Select Geometries 24
Residual Rough Profile 1 leave 0.5 stock 25
Dialog 1 25
Dialog 2 25
Dialog 3 25
Dialog 4 25
Select Geometries 25
Operation 3..................................................................................................... 26
Spot Chamfer 8 dia Holes 1, at Z 0 producing the 1mm x 30 deg chamfer 26
Dialog 1 26
Dialog 2 26
Dialog 3 26
Select Geometries 26
Spot Chamfer 6 dia Holes 3, at Z -3 producing the 1mm x 30 deg chamfer 27
Dialog 1 27
Dialog 2 27
Dialog 3 27
Select Geometries 27
Spot Chamfer 10 Dia Circles 5, at Z-3 28
Dialog 1 28
Dialog 2 28
Dialog 3 28
Select Geometries 28
Operation 4..................................................................................................... 29
Drill 8mm Holes 1, Through 29
Dialog 1 29
Dialog 2 29
Dialog 3 29
Select Geometries 29
Operation 5..................................................................................................... 30
Drill 6mm Holes 3, 10 Deep
30
Dialog 1
30
30
Dialog 2
Dialog 3
30
30
Select Geometries
Drill 6mm Holes 4, Through
31
Dialog 1
31
31
Dialog 2
Dialog 3
31
31
Select Geometries
Version 2
Page 5 of 44
A2
Plik z chomika:
skotisobek
Inne pliki z tego folderu:
ALP_TRG112-134 Material and Tooling Definitions 2012R2 V1.4.pdf
(3183 KB)
ALP_TRG112 Standard Machining 2013R1 V2.1.pdf
(2524 KB)
ALP_TRG112 HP Machining Tutorial 2013 R1 V2.2.pdf
(2097 KB)
ALP_TRG112 Process Plan.pdf
(84 KB)
Router Test.pdf
(143 KB)
Inne foldery tego chomika:
Videos
Zgłoś jeśli
naruszono regulamin